What is the MOQ for wholesale or repair shop orders of the BTY-S1M battery?

We accept low-volume entry orders for repair shops and service centers with no rigid high MOQ requirement. Volume pricing tiers unlock at higher quantities. Contact us directly for a factory quote with current pricing and lead time breakdown.

wholesale-msi-claw-a1m-battery-bty-s1m-main-view

wholesale-msi-handheld-battery-bty-s1m-back-view-bulk

bty-s1m-battery-connector-cable-for-msi-claw-a1m

msi-ms-1t41-battery-label-s9n-0z6a200-aq2-54.5wh-specs

Batterie de remplacement BTY-S1M 11,61 V 4700 mAh 54,5 Wh pour PC de jeu portable MSI Claw A1M

Q: Is the BTY-S1M battery compatible with all MSI Claw A1M models?

Yes. The BTY-S1M covers all four A1M regional variants — A1M-050US, A1M-051US, A1M-019CN, and A1M-025HK — all sharing the same 11.61V / 54.5Wh battery bay and connector spec. Before ordering, open the back panel and confirm the battery label reads BTY-S1M or secondary P/N S9N-0Z6A200-AQ2. Do not order this SKU for the MSI Claw 8 AI+ — that device uses a different, higher-capacity battery.

Q: How long does the MSI Claw A1M battery last per charge, and when should it be replaced?

At full gaming load on the Core Ultra 7 155H at 25 to 35W platform TDP, runtime is roughly 1.5 to 2 hours per charge. At lighter workloads or reduced TDP via MSI Center, 2.5 to 3 hours is achievable. Plan for replacement after 500 to 700 full cycles — typically 18 to 24 months of daily use. Key indicators: runtime drops under 60 minutes, the unit shuts down at 20 to 30% reported charge, or MSI Center shows battery health below 75%.

Q: Does replacing the BTY-S1M battery require recalibration after installation?

No recalibration tool is required, but a conditioning process is recommended. After installation, charge fully to 100%, then discharge to around 15 to 20%, and repeat this cycle 3 to 4 times. This lets the device BMS accurately map the new cell capacity curve. Skipping this does not damage the battery, but reported percentage may be slightly inaccurate for the first few sessions.

Q: What connector type does the BTY-S1M use, and is the swap user-serviceable?

The BTY-S1M uses a multi-pin flex cable connector carrying both power rails and BMS data lines. The MSI Claw A1M back panel is accessible with a Phillips screwdriver. Battery replacement requires removing the back cover, disconnecting the flex cable, and seating the replacement — no soldering needed. Technicians familiar with gaming handheld teardowns can complete the swap in 15 to 25 minutes.

Q: What documentation and shipping options are available for international BTY-S1M bulk orders?

We ship via DHL, FedEx, and sea freight depending on order volume. UN38.3 test reports and MSDS/SDS documentation are provided as standard for all Li-Polymer shipments, covering air freight compliance and customs clearance. Stocked SKU lead time is 3 to 5 business days; OEM-labeled orders run 10 to 15 business days. Full packing declarations can be prepared for sea freight bulk orders on request.

🔋 11.61V / 4700mAh / 54.5Wh — 3-cell Li-Polymer, OEM-matched spec; P/N: BTY-S1M
🎮 Verified compatibility: MSI Claw A1M-050US, A1M-051US, A1M-019CN, A1M-025HK (MS-1T41)
🔌 OEM-matched connector pinout — board-level plug-in replacement, no wiring modification
🛡️ Multi-layer protection PCB: over-charge, over-discharge, short-circuit, thermal cutoff
🏭 Factory direct — 3S2P grade A cell construction, consistent batch spec, low MOQ entry
📦 OEM labeling and custom packaging supported for repair distributors and resellers

Obtenez un tarif dégressif

Description du produit

The MSI Claw A1M was Intel’s first handheld gaming PC built around the Core Ultra 7 155H processor, and MSI engineered the chassis around a compact 54.5Wh battery — a deliberate trade-off between thermal headroom and portability. The OEM battery part number is BTY-S1M, with secondary P/Ns S9N-0Z6A200-AQ2 et 3ICP7/28/78-2 appearing on the physical label. The cell construction is 3S2P — three groups of two parallel Li-Polymer cells in series — giving the pack a 3.87V nominal per-group voltage and a total nominal of 11.61V.

Unlike simpler retro handheld batteries, the Claw A1M’s battery uses a multi-pin flex connector that carries both power and BMS communication data. The replacement must match the original connector spec for the device firmware to read charge state and capacity correctly. This unit does.

Verified Compatible Models & Part Numbers:

Appareil	Référence de la batterie d'origine	Secondary P/N	Capacité	Tension
MSI Claw A1M-050US	BTY-S1M	S9N-0Z6A200-AQ2	54,5 Wh / 4700 mAh	11,61 V
MSI Claw A1M-051US	BTY-S1M	S9N-0Z6A200-AQ2	54,5 Wh / 4700 mAh	11,61 V
MSI Claw A1M-019CN	BTY-S1M	3ICP7/28/78-2	54,5 Wh / 4700 mAh	11,61 V
MSI Claw A1M-025HK	BTY-S1M	3ICP7/28/78-2	54,5 Wh / 4700 mAh	11,61 V

⚠️ Connector verification required. Before ordering, open the back panel of your unit and visually confirm the battery label reads BTY-S1M. The Claw 8 AI+ uses a different battery spec — do not cross-order by brand name alone.

Paramètres techniques

Paramètre	Spécification
OEM Part Number (P/N)	BTY-S1M
Secondary P/N	S9N-0Z6A200-AQ2 / 3ICP7/28/78-2
Tension nominale	11,61 V
Tension de charge complète	12.9V (4.3V × 3 groups)
Capacité nominale	4700mAh / 54.5Wh
Chimie cellulaire	Lithium Polymer (Li-Polymer)
Configuration cellulaire	3S2P (6 cells total)
Qualité cellulaire	Grade A, ≤3% capacity variance
Type de connecteur	Multi-pin flex cable (OEM-matched pinout)
Circuit de protection	Over-charge / Over-discharge / Short-circuit / NTC thermal
Température de fonctionnement	0°C – 45°C (charging); −20°C – 60°C (storage)
Durée de vie du cycle (évaluée)	≥500 cycles à la capacité 80%
Appareils compatibles	MSI Claw A1M-050US / A1M-051US / A1M-019CN / A1M-025HK
Certifications	CE / RoHS / UN38.3
Garantie	12 mois à compter de la date d'expédition

Besoin d'un plan d'approvisionnement stable ? Envoyez-nous la liste des modèles, les quantités et la destination. Nous vous confirmerons le délai de livraison, le mode d'expédition et les documents de conformité avant que vous ne passiez commande.

Obtenez un devis dès maintenant

Caractéristiques et avantages

⚡ Matched to Intel Core Ultra Platform TDP Requirements

The Claw A1M’s Core Ultra 7 155H draws 28–45W at full platform load. The 54.5Wh / 11.61V spec is the minimum pack size MSI validated for stable operation at these draw levels. Undersized or mismatched replacements cause voltage sag under gaming load — this unit maintains the factory-rated discharge profile.

🔌 Multi-Pin Flex Connector — BMS Data Lines Intact

The BTY-S1M connects to the motherboard via a multi-pin flex cable carrying both power and battery management system data. This replacement ships with the correct OEM-matched connector, so the device correctly reports state-of-charge, cycle count, and health status through MSI Center without firmware conflicts.

🔋 3S2P Cell Architecture — Verified 4700mAh Output

The pack uses a 3S2P configuration: six individual Li-Polymer cells arranged as three series groups of two parallel cells each. Rated at 4700mAh total, with <3% capacity variance between production batches. Repair shops get consistent, predictable results across consecutive orders — not spot-market cell variability.

🛡️ Full Protection Circuit — Compatible with MSI BMS Firmware

Over-charge cutoff at 12.9V (4.3V per series group), over-discharge lockout, short-circuit cut, and NTC thermal protection. The protection IC operates in parallel with the device’s own charging controller — no conflict, no false error states after installation.

🏭 Repair Shop Supply Model — Stocked, Not Spot-Sourced

This SKU is maintained as a stocked item from production batches with controlled cell grading. Service centers and distributors building inventory for MSI Claw repairs can order in small batches to start, with tiered pricing opening at higher volumes. Lead time for stocked units is 3–5 business days.

Emballage et livraison

Délai de livraison et expédition

Articles en stock : expédiés sous 3 jours
Pour les modèles de remplacement standard disponibles en stock.
Commandes en gros : expédition sous 7 jours
Pour les modèles standards, sous réserve de spécifications et d'exigences d'emballage confirmées.
Commandes personnalisées : expédition sous 15 jours
Pour une configuration de cellule personnalisée, taille, câblage/connecteur, PCB/BMS, étiquetage ou emballage.

Note: Le délai d'expédition final dépend de quantité totale, complexité du modèle, exigences d'emballage et documents de conformité d'expédition. Nous vous confirmerons la date d'expédition estimée (ETD) après confirmation de la commande.

Modes de livraison disponibles :

Fret aérien (urgent, petit volume)
Transport maritime (économique pour les commandes en gros)
Transport ferroviaire / routier (selon la destination)
Chaînes express

Conformité et documents :

Documents disponibles : UN38.3 / FDS / Rapport d'essai de transport (le cas échéant)
L'emballage conforme et l'étiquetage des cartons peuvent être réalisés en fonction du mode d'expédition choisi.

Conditions d'expédition :

EXW / FOB / CIF / DDP disponibles

FAQ

Q1: Is the BTY-S1M battery compatible with all MSI Claw A1M models?
A: Yes. The BTY-S1M covers all four A1M regional variants — A1M-050US, A1M-051US, A1M-019CN, and A1M-025HK — all of which share the same 11.61V / 54.5Wh battery bay and connector spec. Before ordering, open the back panel and confirm the battery label reads BTY-S1M or secondary P/N S9N-0Z6A200-AQ2. Do not order this SKU for the MSI Claw 8 AI+ — that device uses a different, higher-capacity battery.

Q2: How long does the MSI Claw A1M battery last per charge, and when should it be replaced?
A: At full gaming load on the Core Ultra 7 155H — typically 25–35W platform TDP in-game — runtime is roughly 1.5 to 2 hours per charge. At lighter workloads or reduced TDP settings via MSI Center, 2.5 to 3 hours is achievable. Plan for replacement after 500–700 full cycles, typically 18–24 months of daily use. Clear replacement indicators: runtime drops under 60 minutes, the unit shuts down abruptly at 20–30% reported charge, or MSI Center shows battery health below 75%.

Q3: Does replacing the BTY-S1M battery require recalibration after installation?
A: No recalibration tool is needed, but a conditioning process is recommended. After installation, charge the pack fully to 100%, then discharge to around 15–20% (not 0%), and repeat this cycle 3–4 times. This allows the device BMS to accurately map the new cell’s capacity curve. Skipping this step does not damage the battery, but reported percentage may be slightly off for the first few sessions.

Q4: What connector type does the BTY-S1M use, and is the swap user-serviceable?
A: The BTY-S1M uses a multi-pin flex cable connector carrying both power rails and BMS data lines. The MSI Claw A1M back panel is accessible with a Phillips screwdriver — MSI designed the device as partially user-serviceable. Battery replacement requires removing the back cover, disconnecting the flex cable carefully, and seating the replacement. Technicians comfortable with gaming handheld teardowns can complete the swap in 15–25 minutes. The flex connector is latched, not soldered, so no heat tools are needed.

Q5: What is the MOQ for wholesale or repair shop orders?
A: We accept low-volume entry orders for repair shops and service centers — no rigid high MOQ required. Volume pricing tiers unlock at higher quantities. Contact us directly for a factory quote with current pricing and lead time breakdown.

Q6: What documentation and shipping options are available for international bulk orders?
A: We ship via DHL, FedEx, and sea freight depending on order volume. UN38.3 test reports and MSDS/SDS documentation are provided as standard for all Li-Polymer shipments, covering air freight compliance and customs clearance requirements. For large sea freight orders, full packing declarations can be prepared to buyer specification. Stocked SKU lead time is 3–5 business days; OEM-labeled orders run 10–15 business days.

Vous recherchez d'autres modèles de consoles portables de jeu à distribuer ? Consultez notre catalogue. Batteries pour consoles de jeux portables en gros catégorie pour la fourniture en gros et les prix d'usine.